This content originally appeared on DEV Community and was authored by SigFig Calculator
If you’ve ever reached the end of a calculation and wondered, “How many digits am I allowed to keep?”, this guide is for you. Below you’ll find the core rule when multiplying and dividing significant figures, quick steps, worked examples, and common pitfalls—so your answers are accurate and defensible on labs, tests, and reports.
The golden rule (memorize this)
For multiplication and division, your final answer must have the same number of significant figures as the factor with the fewest significant figures.
That’s it. All the nuance is in counting “sig figs” correctly and rounding the final number (not the intermediate steps).
Quick 4-step method
Count sig figs in each measured value.
Compute using full precision (use your calculator; don’t round midway).
Identify the limiter: the value with the fewest sig figs.
Round the final result to that many significant figures.
Tip: Only round once—at the very end—to avoid compounding rounding error.
How to count significant figures (refresh)
Non-zero digits are always significant: 3.47 → 3 sig figs.
Zeros between non-zeros are significant: 1003 → 4 sig figs.
Leading zeros are not significant: 0.0045 → 2 sig figs.
Trailing zeros are significant if there’s a decimal point: 2.300 → 4 sig figs; 2300 (no decimal shown) is usually 2 sig figs unless otherwise indicated (e.g., 2.300×10³ clarifies 4).
Exact counts (2 beakers, 12 students, defined constants) have infinite sig figs and never limit precision.
Worked examples (with reasoning)
Example 1: Multiplication
Problem: 4.56 cm × 1.4 cm
Sig figs: 4.56 (3), 1.4 (2) → limiter = 2.
Raw product: 6.384 cm².
Rounded to 2 sig figs: 6.4 cm².
Example 2: Division
Problem: 0.00250 kg ÷ 1.25 L
Sig figs: 0.00250 (3; trailing zero after decimal counts), 1.25 (3) → limiter = 3.
Raw quotient: 0.00200 kg/L.
Already 3 sig figs (2.00×10⁻³). Final: 2.00×10⁻³ kg·L⁻¹.
Example 3: Mixed sizes and scientific notation
Problem: (6.022×10²³ molecules) ÷ (3 beakers)
Avogadro’s number is exact by definition in many contexts; “3 beakers” is a count, exact as well.
Exact quantities don’t limit sig figs. The result can be given to the precision required by context or subsequent measurements.
Example 4: Area with ambiguous zeros
Problem: 2300 m × 4.1 m
Sig figs: 2300 (ambiguous—likely 2), 4.1 (2) → limiter = 2.
Raw product: 9430 m².
Rounded to 2 sig figs: 9.4×10³ m².
If the first dimension really had 4 sig figs, write it as 2.300×10³ m to make that clear.
Example 5: Multi-step calculation (don’t round early)
Problem: Density = mass ÷ volume = (12.37 g) ÷ (4.2 mL)
Sig figs: 12.37 (4), 4.2 (2) → limiter = 2.
Raw quotient: 2.945238… g/mL → 2.9 g/mL (2 sig figs).
If you need to use this density later, store the unrounded value and round only for the reported result.
Common mistakes (and easy fixes)
Rounding mid-calculation.
Fix: Keep full precision in your calculator; round once at the end.
Mixing addition/subtraction rules with multiplication/division.
Fix: Remember the difference:
Add/Subtract → limit by decimal places.
Multiply/Divide → limit by sig figs.
Treating counted items as measured.
Fix: Counts and defined constants are exact—they don’t limit sig figs.
Forgetting scientific notation to show precision.
Fix: Use 9.40×10³ to show 3 sig figs instead of 9400 (ambiguous).
Edge cases you’ll see in labs
1) Constants in formulas
When multiplying and dividing significant figures with constants (e.g., π in the area of a circle), treat π as exact for sig-fig purposes unless your instructor specifies otherwise. Precision is limited by your measured radius/diameter.
2) Conversion factors
Common unit conversions (1 in = 2.54 cm, exact by definition; 1 L = 1000 mL, exact) are exact and don’t limit significant figures. If a conversion factor isn’t defined exactly, your instructor will note its precision.
3) Reporting with units and context
Always carry units through the math. Round, then attach units to the final answer. If a context requires more rigor (e.g., engineering specs, quality control), include tolerance or uncertainty separately from significant figures.
Quick reference table
Operation
Limiting rule
Example
Result
Multiply
Fewest sig figs
5.10 × 2.3
12 → 12 (2 sf)
Divide
Fewest sig figs
15.6 ÷ 4.0
3.9 (2 sf)
Add/Subtract
Fewest decimal places
2.45 + 3.1
5.6
(sf = significant figures)
Practice set (answers below)
3.22×7.13.22 \times 7.1
0.00450÷2.50.00450 \div 2.5
(6.0×102)×(3.10×10−3)(6.0\times10^2) \times (3.10\times10^{-3})
1250÷3.01250 \div 3.0
Answers
22.862 → 23 (2 sf)
0.0018 → 0.0018 (2 sf → 1.8×10⁻³)
1.862×10⁰ → 1.86 (3 sf vs 2 sf? Check: 6.0 has 2 sf, 3.10 has 3 sf → 2 sf ⇒ 1.9)
416.666… → 4.2×10² (2 sf—because 3.0 has 2 sf; 1250 is likely 3 sf but ambiguous—write 1.250×10³ to force 4 sf)
A note on calculators and rounding modes
Set your calculator to show plenty of digits (8–12) while you work. After identifying the limiter, round correctly:
Round up if the next digit is 5–9.
Round down if it’s 0–4.
For long chains of operations, keep the unrounded value in memory; only round your reported result.
Summary you can tape to your notebook
Multiply/Divide → match the fewest sig figs among inputs.
Add/Subtract → match the fewest decimal places.
Counts & defined conversions are exact (don’t limit).
Round once at the end, then attach units.
Use scientific notation to show intended precision.
Master these rules, and every answer you submit will look clean, consistent, and scientifically credible—exactly what graders and lab partners love to see.
This content originally appeared on DEV Community and was authored by SigFig Calculator
SigFig Calculator | Sciencx (2025-09-27T04:34:34+00:00) When Multiplying and Dividing Significant Figures: The Complete, No-Stress Guide. Retrieved from https://www.scien.cx/2025/09/27/when-multiplying-and-dividing-significant-figures-the-complete-no-stress-guide/
Please log in to upload a file.
There are no updates yet.
Click the Upload button above to add an update.